Flood risk assessments are typically based on scenarios which assume homogeneous return periods of flood peaks throughout the catchment. This assumption is unrealistic for real flood events and may bias risk estimates for specific return periods. We investigate how three assumptions about the spatial dependence affect risk estimates: (i) spatially homogeneous scenarios (complete dependence), (ii) spatially heterogeneous scenarios (modelled dependence) and (iii) spatially heterogeneous but uncorrelated scenarios (complete independence). To this end, the model chain RFM (regional flood model) is applied to the Elbe catchment in Germany, accounting for the spatio-temporal dynamics of all flood generation processes, from the rainfall through catchment and river system processes to damage mechanisms. Different assumptions about the spatial dependence do not influence the expected annual damage (EAD); however, they bias the risk curve, i.e. the cumulative distribution function of damage. The widespread assumption of complete dependence strongly overestimates flood damage of the order of 100 % for return periods larger than approximately 200 years. On the other hand, for small and medium floods with return periods smaller than approximately 50 years, damage is underestimated. The overestimation aggravates when risk is estimated for larger areas. This study demonstrates the importance of representing the spatial dependence of flood peaks and damage for risk assessments.
Floods frequently occur as destructive events throughout the world. In the period 1995–2015, there were around 3100 flood events which affected 2.3 billion people worldwide with overall damages of USD 662 billion (CRED and UNISDR, 2015). It is commonly stated that flood risk has increased rapidly in the past and will continue to increase in future due to the combined effects of climate change and socio-economic development (e.g. Rojas et al., 2013). In order to mitigate the destructive impacts of floods, sound flood risk assessment and management are essential.
During the last decades, flood risk management has gained considerable attention and has shifted from a hazard-focused approach to the broader risk-based perspective covering both physical and societal processes (e.g. Merz et al., 2010, 2014a; Bubeck et al., 2016; Thieken et al., 2016). For instance, the EU Flood Directive (EC, 2007) was adopted in October 2007 to launch a flood risk assessment and management framework in Europe considering all aspects of flood risk, including the impacts on society.
Conceptually, flood risk is defined as the probability of the adverse consequences within a specified time period. It depends on three components: hazard, exposure and vulnerability (IPCC, 2012; UNISDR, 2013). Following this definition, flood risk assessment starts with quantifying the hazard. By combining hazard and socio-economic information, such as land use and asset values, exposure is assessed. Vulnerability is included by adding information on how flood-affected objects would be damaged. Overall, flood risk assessment attempts to estimate the characteristics, e.g. inundation depth and flood extent, of a range of potential flood events, the exceedance probabilities of these events and their consequences (e.g. Winsemius et al., 2013; de Moel et al., 2015). The results of flood risk assessments are often presented in maps, which exist in many different forms depending on their purpose (Merz et al., 2007; de Moel et al., 2009). Flood hazard maps contain flood characteristics, e.g. inundation extent and water depth, for given return periods. Flood risk maps additionally consider the adverse consequences, e.g. economic damage and number of affected people.
Flood mapping is typically based on a number of spatially uniform (or
homogeneous) scenarios with given return periods (e.g. Rhine
Atlas; ICPR, 2015). The scenario with a
Some studies consider the spatial variability in return periods of floods. One approach applies multi-variate distribution functions to represent the dependence between flood peaks at multiple sites (e.g. Keef et al., 2009; Lamb et al., 2010; Ghizzoni et al., 2012; Thieken et al., 2015; Quinn et al., 2019). Based on a stochastic dependence model, spatially heterogeneous scenarios are generated and used for the risk assessment. This approach provides, however, only flood peaks, whereas the transformation of peaks into inundation areas requires event hydrographs. Hence, synthetic hydrographs are associated with the peaks, which is an additional source of uncertainties and errors (Grimaldi et al., 2013). These hydrographs are spatially inconsistent, i.e. not mass conservative, (though peaks are spatially consistent) and can be used for hydraulic calculations only for a limited river stretch. Another approach, proposed by Alfieri et al. (2015, 2016, 2017), combines inundation maps and resulting risk for heterogeneous return periods piecewise by interpolating between previously derived homogeneous return period maps. The spatially variable discharges are derived from a hydrological model driven by observations or climate models. This approach considers spatial dependence but still suffers from inconsistencies of inundation maps mosaicked piecewise. Further, an event-based simulation approach, where stochastic precipitation events are generated as input to a hydrological model, has been used (e.g. Rodda, 2001; Jankowfsky et al., 2016). The hydrological model simulates spatially dependent discharge hydrographs, which are then used by the hydrodynamic model to map inundated areas. A disadvantage of this approach is that the return period of discharge is assumed to be equal to the return period of precipitation, an assumption that does not necessarily hold. An alternative approach is a continuous hydrological–hydrodynamic simulation driven by long-term synthetic climate time series (e.g. Falter et al., 2015; Grimaldi et al., 2013). This approach is computationally expensive; however, it has a number of advantages, as discussed by Falter et al. (2015). Within the context of this paper, its most relevant advantage is that spatially consistent flood events can be modelled by considering the spatial dependence of the precipitation and of the flood generation processes in the catchment and river network.
According to our literature review, only a few studies consider spatial dependence when assessing flood risk. The large majority assume spatially homogeneous scenarios. This assumption is also the basis for flood hazard mapping, for instance, in Europe (de Moel et al., 2009), in Iowa in the US (Gilles et al., 2012), in Bangladesh (Tingsanchali and Karim, 2005) and in Honduras (Mastin, 2002). The assumption of complete dependence is appropriate for local risk estimates, but it may bias the risk estimates for larger areas. The purpose of our paper is to investigate this bias. To understand the effect of spatial dependency on risk estimates, we compare three assumptions of spatial dependence: (i) spatially dependent flood events with homogeneous return periods (complete dependence), (ii) spatially dependent events with heterogeneous return periods (modelled dependence) and (iii) spatially independent events with heterogeneous, i.e. randomly selected, return periods (complete independence). We explore the variation in the dependence effect with spatial scale and flood magnitude with respect to resulting flood damage.
To the best of our knowledge, our study is the first in-depth analysis of
this bias at the scale of a large river basin.
Lamb et al. (2010) and
Wyncoll and Gouldby (2015) compared risk estimates for these
three assumptions for smaller regions in the UK only (Leeds, York: around 12 000 km
To realistically represent the spatial dependence of the different flood processes, we use the derived flood risk analysis (DFRA) based on continuous spatially consistent modelling of the entire flood process chain (Falter et al., 2015). The model chain includes all processes from the precipitation through the catchment and river system to the damage mechanisms. The effect of spatial dependence is investigated for the Elbe catchment in Germany.
This paper is organized into six sections. Section 2 introduces the study area. Section 3 describes the model chain and how the risk estimates are obtained for the three dependence assumptions. Section 4 illustrates the risk estimation results under three spatial dependence assumptions. Further, we discuss these results in Sect. 5 and draw conclusions in Sect. 6.
The river Elbe is located in central Europe, with a length of 1094 km and
total catchment area of 148 268 km
Floods occur mainly in winter and spring, often as snowmelt or rain-on-snow floods. However, the largest floods tend to occur in summer. Heavy precipitation events associated with Vb cyclones have caused disastrous floods, such as the events in August 2002 and June 2013. The 2002 (EUR 8.9 billion damage) and 2013 flood events (EUR 5.2 billion) were the most severe flood events in the Elbe River basin in Germany for the last few decades (IKSE, 2015). Besides this, the river basin was affected by smaller floods in 2006, 2010 and 2011.
Study area in the Elbe catchment, including the main tributaries and sub-basins. The inset shows the location of the catchment within Germany. Data sources of figure: BKG (2012).
The regional flood model (RFM) has been developed for large-scale flood risk
assessments, i.e. for areas of up to several 100 000 km
In this study, RFM is run for time series of 10 000 years (100 realization of 100 years) on a daily time step. Synthetic meteorological time series at multiple sites are provided by a multi-variate weather generator. Further, continuous flood hydrographs at the sub-basin scale are calculated by a hydrological model, where antecedent catchment conditions are implicitly considered. The flow hydrographs are used as a boundary condition for the calculation of water levels in the river channels and inundation depths with a coupled 1-D–2-D hydrodynamic model considering levee overtopping. Finally, damage time series using a multi-variate flood loss estimation model for residential buildings are simulated. In this way, spatially consistent time series of flood damages at the SWIM sub-basin scale (196 sub-basins) are derived. The final risk results are represented at the grouped sub-basin scale (29 sub-basins). The model components are briefly described in the following. Details about RFM and calibration and validation results of the model components can be found in Falter et al. (2015, 2016) and Metin et al. (2018).
Workflow for the derived flood risk assessment (DFRA) with the regional flood model (RFM).
The regional weather generator (RWG), proposed by Hundecha et al. (2009) and further developed by Hundecha and Merz (2012), generates synthetic weather at the regional scale. This multi-site, multi-variate auto-regressive model generates daily time series of meteorological variables, taking into account the spatial correlation structure. First, it generates daily precipitation series using the mixed gamma–Pareto distribution fitted to the observed data. Further, the model generates daily maximum, minimum and mean temperature and solar radiation using Gaussian distributions conditioned on precipitation. RWG was set up for the area covering the entire Elbe, Rhine, Danube and Ems rivers using the observed climate data at 528 climate stations between the year 1951 and 2003 and was shown to capture daily precipitation extremes and seasonal precipitation patterns well (Hundecha et al., 2009).
Discharge time series on a daily basis are derived with the semi-distributed
hydrological model SWIM (Krysanova et al.,
1998). The model has a three-level structure of spatial disaggregation:
basins, sub-basins and hydrotopes. A hydrotope is a set of disengaged
elementary units within the sub-basins, which are homogeneous in terms of
land use and soil type. The hydrological processes, such as
evapotranspiration, infiltration and snowmelt, and different types of
runoff are computed at the hydrotope level. The outputs from hydrotopes are
integrated (area-weighted average) for each sub-basin. An average sub-basin
area is in a range of 10 to 100 km
The Elbe catchment was discretized into 2268 sub-basins in the watershed
delineation of the SWIM model (SWIM sub-basins). A detailed soil map
(BÜK 1000 N2.3, generated by the Bundesanstalt für Geowissenschaften
und Rohstoffe, Hannover) and land use data (the CORINE land cover map) were
used. The model was calibrated using observed daily climate data for the
period 1981–1989. It was validated with observed discharge data on 20
gauging stations in the Elbe catchment for 1951–2003
(Falter
et al., 2015; 2016; Metin et al., 2018). While discharge is simulated well
in most parts of the Elbe catchment, peak flows are over- and underestimated
in the range of
The RIM simulates the water level along the
river network and hinterland inundation depths. RIM consists of two-way
coupled models: a 1-D hydrodynamic channel-routing model based on the
diffusive wave equation and a raster-based 2-D hydrodynamic inundation model
based on the inertia formulation (Metin et al., 2018). The overtopping flow
is calculated by the 1-D model and is used as boundary condition for the 2-D
model, which is back-coupled to the 1-D model. The overtopping is considered
only at the main river network and higher-order tributaries that have a
drainage area of 600 km
The river profiles were manually extracted perpendicular to the flow
direction every 500 m. Due to the low resolution of the 10 m DEM in relation to
the dike geometry, the derived dike heights tend to be lower than in
reality. Hence, a minimum dike height of 1.8 m was used for the river Elbe.
The constant Manning's roughness of 0.03 m
The 1-D hydrodynamic channel-routing model was validated with observed data for 1951–2003 at eight gauging stations in the Elbe catchment (Falter et al., 2015, 2016). The performance of the 1-D model is acceptable even though there is a tendency to underestimate observed peak flows exceeding the bankfull depth. The simulated inundation areas were compared to the extreme flood in August 2002, the only event for which inundation depth and extent are available. Although the model tends to underestimate inundation extents, since it neglects dike breaches, it provides plausible inundation patterns.
The direct economic damage to residential buildings is estimated by the Flood Loss Estimation MOdel for the private sector (FLEMOps
Besides inundation depths and return periods, the model requires spatially detailed information on building qualities, building types and asset values. The mean building quality and cluster of building type composition was estimated on the municipal level on basis of INFAS Geodaten GmbH (2009). The asset values were determined considering the standard construction costs (BMVBW, 2005) and were spatially disaggregated using the digital basic landscape model ATKIS Basis DLM (BKG GEODATENZENTRUM, 2009). Municipal asset data were disaggregated by means of a dasymetric mapping approach (Wünsch et al., 2009). The damage was estimated according to output from the hydrodynamic model on a raster level by calculating the damage ratio according to the inundation depth and return period in the corresponding cell and the underlying information for building types and qualities per municipality (Thieken et al., 2008).
The model was validated on the micro- and meso-scale on basis of empirical damage data of the August 2002 flood in the state of Saxony in Germany (Elmer et al., 2010; Falter et al., 2015).
We compute flood risk for three spatial dependence assumptions (Fig. 3): (1) complete dependence or homogeneous return periods across the river basin, (2) modelled dependence or heterogeneous return periods, and (3) complete independence, where flood peaks and associated return periods are randomly sampled. In scenarios (1) and (3) the discharges, inundation areas and damages are spatially inconsistent; i.e. they are mosaicked from the continuous simulations by selecting events and damages for corresponding return periods. The spatial variation in damages within the catchment depends on the spatio-temporal patterns of meteorological, hydrological and hydraulic processes. For instance, the flood damage downstream of the confluence of two tributaries depends on the superposition of the flood waves from these tributaries. The damage results of the modelled dependence should lie between the results of the two other assumptions, as they span the whole range from complete dependence to complete independence. Further, the modelled dependence results should be similar to those of the complete dependence for small areas and should move towards complete independence as the spatial scale becomes large.
Conceptual representation of the three assumptions on spatial
dependence:
We characterize flood risk by the probability of damage (risk curve) and by the expected annual damage (EAD) computed as the integral of the risk curve. Damage values are calculated at the 100 m grid resolution for individual inundation events of the 10 000-year continuous flood simulation with RFM. An event requires that flood defences are overtopped at least at one location and that it affects residential assets, i.e. a non-zero damage occurs. If anywhere in the entire catchment overtopping occurs after at least 10 d of non-overtopping, this is defined as the start of a new event. Empirical return periods for damages aggregated for specific spatial units (e.g. sub-catchments) are determined using Weibull plotting positions. Damage at the level of the sub-basins (SWIM sub-basins) is then aggregated to larger spatial units (e.g. aggregation of sub-basins or the entire catchment) for individual flood events. These pairs, i.e. damage and associated return period, are used to construct risk curves and to calculate the EAD (Falter et al., 2015).
Under the assumption of complete dependence, all sub-basins within the
considered spatial unit, e.g. the entire river basin, are assumed to
experience a
Under the modelled dependence assumption, damages are aggregated for
individual flood events across the considered spatial unit, and return
periods of aggregated damages are derived directly for this spatial unit.
This approach aims to represent the true spatial and temporal dependencies
of real-world flood situations. For example, for a
Under the assumption of complete independence, the spatial correlations between damages of different sub-basins are destroyed. Damages of individual flood events are shuffled at the SWIM sub-basin level and aggregated for the considered spatial units. Return periods of these aggregated damages are determined for the spatial unit considered. As the aggregated damage and the risk curve depend on the specific realization of the shuffling, this procedure is repeated 1000 times. From this sample, the median is used to construct the risk curve, and additionally the 95 % confidence range is computed.
The risk curves and EAD are derived at the grouped sub-basin level (29 sub-basins in total; see Fig. 1), as a higher resolution would lead to many instances where the number of damaging floods would be too low to construct meaningful empirical risk curves.
The aggregated economic damages to residential buildings for the Elbe catchment and their corresponding return periods are illustrated in Fig. 4 for the three dependence assumptions. While the economic damage of the 1000-year event is estimated at around EUR 620 million under the assumption of complete dependence, it is around EUR 360 million for the modelled dependence scenario (70 % overestimation under the assumption of complete dependence). A strong overestimation is also given for smaller return periods down to approximately 150 years. Moreover, the assumption of complete independence may underestimate damage by 50 %. The extreme assumption of complete independence represents the lower limit for large return periods. For smaller return periods, however, we see the opposite effect. The damage is underestimated under the assumption of complete dependence for events with return periods smaller than 87 years.
The point where the risk curves of modelled dependence and complete dependence intersect is called the “intersection point” in the following. For return periods up to this intersection point, the complete dependence assumption underestimates the damage compared to modelled dependence; all sub-basins show either no or small damages, as the flood peaks are mostly below the flood defences. However, for the assumption of modelled dependence, the return periods vary, and a small to medium return period event at the scale of the entire Elbe catchment may be composed of many sub-basins without any damage but a few sub-basins with large damage because in these sub-basins the flood defences are overtopped. A similar explanation holds for the situation beyond the intersection point: the complete dependence assumption leads to events where all sub-basins tend to show large damages, as flood defences are overtopped everywhere. In contrast, under the modelled dependence assumption many sub-basins show large damages as defences are overtopped; however there are also sub-basins without damage as a consequence of spatial variability.
Risk curves for the Elbe catchment for three dependence assumptions (complete dependence, complete independence and modelled dependence). The left panel zooms in on the risk curves up to the 100-year return period of damage.
The underestimation (overestimation) for small (large) return periods under the complete dependence assumption is a consequence of the strong link between the damages of the different sub-basins. For better understanding, Fig. 5 illustrates the spatial distribution of damages at the sub-basin level for the three dependence assumptions that lead to the 20- and 200-year event at the catchment scale. For the 20-year event, under the complete dependence assumption, all sub-basins show either no damage or small to medium damage, leading to comparatively small damage at the scale of the entire basin (Fig. 5a). The 20-year event for the modelled dependence assumption consists mainly of sub-basins without any damage, but due to dike overtopping single sub-basins may experience large damage. These sub-basins are clustered, in this case in the northwest of the Elbe catchment, illustrating the effect of spatial dependence. In contrast, the damages are not clustered under the complete dependence and independence assumptions. For the 200-year event (Fig. 5b), almost all sub-basins indicate large damage under the complete dependence assumptions, resulting in the overestimation under complete dependence assumption for the entire catchment.
Distribution of damages at the sub-basin level for
To understand how the risk estimates for the three dependence assumptions vary with spatial scale, the risk curves for aggregations of sub-basins from upstream to the entire catchment are given in Fig. 6. As a general rule, smaller regions should be characterized by stronger spatial dependence of damage. This should lead to (1) an increasing difference between the risk curves of the three dependence assumptions with increasing scale and (2) a shift of the modelled dependence risk curve from the complete dependence towards independence with increasing scale. Both effects are seen in Fig. 6.
The intersection point shifts from return periods of a few hundred years for
smaller aggregation areas, i.e. sub-basins 1 to 8 (up to 11 800 km
Sub-basins in the Elbe catchment (left) and risk curves of aggregations of sub-basins (right) under complete dependence, modelled dependence and independence. The aggregated sub-basins are ordered along increasing scale and are denoted by green within each risk curve and the colon (:) between start and end sub-basin numbers.
Besides the risk curve, the EAD and the damage for a
Percentage error in expected annual damage (EAD)
This study investigates the effects of spatial dependence of flood generation processes on risk estimates. It compares the “true” dependence scenario to the two endpoints, i.e. complete dependence and complete independence. It is shown that the assumption of complete spatial dependence, which is often used in risk assessments, leads to under- and overestimation of flood risk for small and large return periods, respectively.
Although several papers have suspected that the complete dependence
assumption may bias risk estimates, this bias has been investigated by the
two studies of Lamb et al. (2010) and
Wyncoll and Gouldby (2015) only. As these studies are limited
to small and medium study areas up to 15 000 km
We are not aware of any study which discussed the intersection point between modelled and complete dependence. We show that the overestimation of risk by the complete dependence assumption that has been reported by Lamb et al. (2010) and Wyncoll and Gouldby (2015) applies to large return periods only. For small return periods the complete dependence assumption underestimates risk. This behaviour, and the location of the intersection point, is mainly affected by the damage threshold controlled by the flood defence level or elevated banks.
Although each model in RFM has some limitations, RFM represents well the spatial patterns of the different flood generation processes (Falter et al., 2016; Metin et al., 2018). For this study, the model limitations of hydrologic, hydraulic and damage model accuracy are not seen as major concerns because the different assumptions on spatial dependence are investigated by using the same model chain. The spatial performance of the weather generator with regards to precipitation, however, can have an effect on the final results. It is also more challenging for the weather generator than capturing the local statistics as previously discussed in the literature (e.g. Serinaldi and Kilsby, 2014). The spatial dependence of high precipitation is often overestimated due to the use of isotropic covariance function (Serinaldi and Kilsby, 2014) as also applied in our case. Although this limitation would presumably translate into the higher dependence of discharge peaks, we believe, this is not critical for the presented study. The results of modelled dependence are located between complete dependence and complete independence for high return periods. With an ideal weather generator, they would be closer to the complete independence. Thus, our estimates for the difference between the assumption of complete dependence and modelled dependence can be regarded as conservative. Hence, the major conclusion challenging the assumption of homogeneous return periods (complete dependence) still holds. Another limitation is the assumption that dikes can only be overtopped but do not breach. In reality, dike breaches may lead to significant reductions of flood peaks downstream of breach locations, and larger outflow volumes can be observed in the inundated area compared to the no-breach case. However, the modelling of dike breaching requires high computational time because the prediction of breach locations is difficult, and hence a stochastic approach including multiple Monte Carlo runs would be needed. In this study, the consideration of dike breaching would increase the computational time, which is already high. Hence, the number of inundation events and damages may be underestimated. This could affect the intersection point, i.e. the point where the underestimation of the complete dependence turns into overestimation. Including dike breaches in the model might shift the intersection point to smaller return periods.
As expected from statistical reasoning, our study confirms that the EAD is not biased by false assumptions on spatial dependence. If one is only interested in the EAD, spatial dependence can be neglected, which drastically simplifies the analysis. However, the EAD is a rather limited indicator of risk, as discussed, for instance, by Merz et al. (2009). Further, specific purposes demand assessments of certain risk scenarios for which spatial dependence is crucial. According to Article 101 of the European Solvency II Directive, insurance companies are required to prove that they can cover at least damage events with a return period of 200 years (EC, 2009). The spatial dependence in damage is also highly relevant for disaster management or large-scale, strategic flood planning. It is important, for instance, to understand the disaster management resources that are needed for large-scale floods.
This paper analysed the impact of spatial dependence in flood damage generation on risk estimates for the large-scale Elbe River basin in Germany. The “true” spatial dependence was simulated with the continuous flood risk modelling approach proposed by Falter et al. (2015), where all processes, including their spatial dependence, from the flood-triggering rainfall to the damage processes, are considered. The bias between the widespread but false assumption of complete dependence and the modelled dependence was investigated as a function of spatial scale.
Our results show that for extreme events the economic damage can be strongly overestimated when homogeneous return periods are assumed across the catchment. For the Elbe River basin, damage is overestimated by about 40 % for the 200-year event and by almost 100 % for the 500-year event. On the other hand, for events with small to medium return periods, the complete dependence assumption underestimates damage. The intersection point where the underestimation turns into an overestimation depends mainly on the damage threshold, i.e. on the flood defence level in protected areas.
The spatial scale, for which a risk estimate is sought, decides whether the modelled dependence assumption is closer to complete dependence or independence, respectively. The modelled dependence risk curve is closer to complete dependence for the upstream areas comprising the Mulde and Black Elster rivers; with increasing scale it shifts towards the independent case. Consequently, the overestimation under the complete dependence assumption increases with larger areas. As a general rule, the true dependence might be approximated by the complete dependence assumption for smaller regions, whereas for larger regions the independence assumption might serve as an approximation in a rough analysis when including the spatial dependence seems too costly or demanding. However, our study does not allow specifying in a generic way the scales at which a certain assumption might serve as approximation. More systematic analyses are necessary to answer this question.
If one is only interested in the expected annual damage (EAD), then false assumptions on spatial dependence do not bias its estimate. Although the EAD is an important risk indicator, for example for cost–benefit analyses of flood mitigation or in the insurance sector, we strongly advocate considering the complete risk curve, as it gives a much richer perspective on the risk and the effects of mitigation measures. Hence, we conclude that it is of highest relevance to realistically represent the spatial dependence of flood damage for large-scale risk estimates.
The data used in this paper are not publicly accessible; however, the authors can be contacted by email (admetin@gfz-potsdam.de, dung@gfz-potsdam.de, kai.schroeter@gfz-potsdam.de) for help in acquiring such data.
BM conceived and supervised the study. BM, ADM, NVD and SV developed the concept. NVD, KS and ADM performed simulations. ADM analysed the results. ADM prepared the paper, with contributions from all the co-authors. All authors made a substantial contribution to the interpretation of results and provided important ideas to further improve the study.
The authors declare that they have no conflict of interest.
We gratefully acknowledge funding from the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement no. 676027 and from the German Research Foundation (DFG Research Group FOR 2416 SPATE). We thank the Federal Agency for Cartography and Geodesy in Germany (BKG) for providing DEM data. We further thank Attilio Castellarin and one anonymous referee for their valuable input.
This research has been supported by the European Union's Horizon 2020 research and innovation programme under a Marie Skłodowska-Curie grant (grant no. 676027) and the German Research Foundation (Deutsche Forschungsgemeinschaft – DFG; grant no. FOR 2416).The article processing charges for this open-access publication were covered by a Research Centre of the Helmholtz Association.
This paper was edited by Maria-Carmen Llasat and reviewed by Attilio Castellarin and one anonymous referee.